#Copy ios to tftp install
#Copy ios to tftp serial
#Copy ios to tftp Pc

#Copy ios to tftp serial

**Make sure you have the driver software installed for the USB to Serial Converter. **Make sure the Device is powered on and Cosole cable is properly fitted. **Connect the both Ethernet and Console Cables to your laptop and connect via Xshell. **At this stage you will not able to Ping your Router IP 10.0.0.1. My Computer Ethernet adapter Local Area Connection: Select your COM Port via вЂњMy Computer->Manage->Device Manager->Other Devices->Ports (COM & LPT) вЂќ and set XShell Session to that PORT.

Step 2 : Setup your XSHELL as above and connect to the Router. This is all you need to do on TFTPd32 Software. > No changes required on вЂњDHCPвЂќ and вЂњSYSLOGвЂќ tabs. Tick Option negotiation,show progress bar,Translate unix file names ,Bind TFTP to this address вЂњ10.0.0.2вЂќ,Allow вЂњвЂќ as virtual root. >Browse the image file as the вЂњBase DirectoryвЂќ

>Tick only вЂњTFTP ServerвЂќ and leave all unselected Server Interfaces = use вЂњ10.0.0.2вЂќ interface (Your LAN Wired Interface IP connected to Router LAN Port)

#Copy ios to tftp install

Step 1 :Configuring a TFTP server on your Laptop.Дownload the вЂњtftpd32вЂќ software from the internet and install on your laptop. Method 1 : Use of My laptop as the TFTP Server ROMMON or also known as bootstrap program. If the router is trying to boot from corrupted IOS then hard boot agian and press Ctrl + Function + Break Button to go into ROMMON mode.

#Copy ios to tftp Pc

You need to connect to the Router using two cables.Ethernet and Console.Connect to the Router via your PC with the Console port using a console cable.ДЄlso PC( TFTP server) is connected to the first LAN Port of the router. In our scenario, we have given the name routerios.bin.ДЄfter we have entered these commands, we will again enter the command tftpdnld.ДЄfter that, it will ask us to continue to say yes (as shown in the figure) if we have entered the right parameters otherwise enter no and again specify the correct parameters.ДЄfter that just enter command reset to reload the router.1) Cisco IOS image copied to TFTP server installation directory.Дў) Enough Router Flash Memory to copy the file.ДЈ) PC connected to routers Ethernet port.

TFTP_FILE вЂ“ It is the name of the file which we have saved on the TFTP server.

TFTP_server вЂ“ This command requires the IP address of the TFTP server which is 10.1.1.2 in our scenario.

Here, notice that our TFTP server is directly connected to the routerвЂ™s interface, therefore, we can give the TFTP serverвЂ™s IP address which has been given as 10.1.1.2 but if there is any router in between TFTP server and router then we have to give the default gateway IP address of the router.

DEFAULT_GATEWAY вЂ“ Here, we have to give the default gateway for that routerвЂ™s interface IP address.

IP_SUBNET_MASK вЂ“ This is the subnet mask that we want to give to the routerвЂ™s interface IP address which is 255.255.255.0 in our scenario.

Here, we have provided 10.1.1.1 on the routerвЂ™s interface.

IP_ADDRESS вЂ“ It is the IP address we want to give to our routerвЂ™s interface fa0/0 but remember this IP address should be of the same subnet.

Now, as soon as we type this command, we see that the parameters which we have to enter next. Therefore, now to copy the IOS file from TFTP server we will use the command: Therefore, when we will reload the router, it will enter ROMMON mode. Now, as the file is deleted still the router is running because the IOS has already been loaded into RAM. Now, we will delete the IOS image from the router: Here, we have named it as routerios.ДЄs shown in the above figure, the file has been copied to the TFTP server.

Destination filename вЂ“ It is the name of the destination file that will be put in the TFTP server.

Address or name of remote host вЂ“ It is the IP address of the TFTP server.

here, it is named 1.bin (shown in flash).

Source filename вЂ“ It is the name of the IOS image file.

Now, as we can see in the above image it is asking for source filename, Address of remote host, and destination filename. Source filename? 1.binДЄddress or name of remote host ? 10.1.1.2Дestination filename ? routerios Now, we will copy this file to our Tftp server by command:

Difference between Private and Public IP addresses.

Difference between Synchronous and Asynchronous Transmission.

nslookup command in Linux with Examples.

Implementation of Diffie-Hellman Algorithm.

Transmission Modes in Computer Networks (Simplex, Half-Duplex and Full-Duplex).

Types of area networks - LAN, MAN and WAN.

Network Devices (Hub, Repeater, Bridge, Switch, Router, Gateways and Brouter).

ISRO CS Syllabus for Scientist/Engineer Exam.

ISRO CS Original Papers and Official Keys.

GATE CS Original Papers and Official Keys.